 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| RF AMPLIFIER MODEL CZ8310 Features ! ! ! ! Lower Cost; Medium Gain: 8 dB Typical Noise Figure: < 7 dB Typical Operating Temp. 0 C to +70 C Environmental Screening Available Available as: CZ8310, 3 Pin TO-39 (T10) TN8310, 4 Pin Surface Mount (SM3) FP8310, 4 Pin Flatpack (FP4) BX8310, Connectorized Housing (H1) Typical Intermodulation Performance at 25 C Second Order Harmonic Intercept Point........+13 dBm (Typ.) Second Order Two Tone Intercept Point...........+8 dBm (Typ.) Third Order Two Tone Intercept Point...............+7 dBm (Typ.) Specifications CHARACTERISTIC Frequency Gain (dB) Power @ 1 dB Comp. (dBm) Reverse Isolation (dB) VSWR In Out Noise figure (dB) Power Vdc mA TYPICAL Ta= 25 C kHz -1000 MHz 8 -1.5 - 13 < 2.5:1 < 2.5:1 < 7.0 + 1.6 10 MIN/MAX Ta = 0 C to +70 C kHz - 1000 MHz 7.0 Min. -4.0 Min. -12.0 Max. 3.5:1 Max. 3.0:1 Max. 8.0 Max. +1.6 12 Max. Maximum Ratings Ambient Operating Temperature .............. -55C to + 125 C Storage Temperature ............................... -62C to + 125 C Case Temperature ................................................. + 125 C DC Current .............................................................. 25 mA Continuous RF Input Power ................................... + 6 dBm Short Term RF Input Power ...... 25 Milliwatts (1 Minute Max.) Maximum Peak Power ................... 0.25 Watt (3 sec Max.) Note: Care should always be taken to effectively ground the case of each unit. Typical Performance Data Gain (dB) 10 9 8 7 6 Start KHz Stop 1000 MHz Reverse Isolation (dB) 0 -5 - 10 - 15 - 20 Start KHz Stop 1000 MHz Noise Figure (dB) 8 7 6 5 4 Start KHz Stop 1000 MHz +4 +2 0 -2 -4 Start KHz 1 dB Comp. (dBm) Input VSWR 3.0 2.0 1.0 2.0 1.5 1.0 Start KHz Stop 1000 MHz Start KHz Output VSWR Stop 1000 MHz Stop 1000 MHz Legend +25 C +70 C - - - - - - 0 C * Decoupling Impedance is 1 KOhm The CZ83X0 Series Amplifiers are designed for application in 50 ohm systems. Three external capacitors and a decoupling impedance are required. The decoupling impedance must be large in comparison to the 50 ohm load to minimize gain reduction. Data sheet curves are based on the noted decoupling impedance. The external capacitors determine the low frequency recponse of the Amplifier. The CZ83X0 Series Amplifiers can be cascaded in series of two or more units without oscillation problems. Schematic Diagram +Vcc CZ Series Amp Decoupling Impedance 50 Ohm Input 50 Ohm Output Spectrum Microwave * 2144 Franklin Drive N.E. * Palm Bay, Florida 32905 * PH (888) 553-7531 * Fax (888) 553-7532 10/13/04 www.SpectrumMicrowave.com Spectrum Microwave (Europe) * 2707 Black Lake Place * Philadelphia, Pa. 19154 * PH (215) 464-4000 * Fax (215) 464-4001 |
Price & Availability of CZ8310
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |